Free Shipping on Orders $99.00+ Earn Reward Points with Every Order! Read more.

Trigger Systems Emerald 26 Sump

Sku: TS-EMERALD26

More Views

Trigger Systems Emerald 26 Sump

Sku: TS-EMERALD26

$324.99

Availability: Call For Availability

Reward Points You will earn 20 Points for writing a review and 20 Points for rating this product.

The Emerald series introduces several new features not found anywhere else. Some of the features of the Emerald sumps are:

  • Interchangeable plates (Patent Pending)
  • Lid to prevent splashing
  • Adjustable water height
  • Self adjusting foam block platform (Patent Pending)
  • Dual platforms
  • Protein skimmer section
  • Refugium section
  • Emerald green coloring to block light and prevent unwanted algae growth in other sections
  • Laser engraved water level indicator
  • Laser etched lid
OR
Description

Details

Emerald 26 Specifications:

  • Dimensions: 26″ long x 13″ wide x 15″ high
  • Skimmer Section: 8.25″ x 10″
  • Center/Refugium Section: 7.75″ x 12.5″
  • Return Pump Section: 5″ x 12.5″
  • Total Water Volume: 20.4 gallons
  • Skimmer Water Level: 7″ to 9.5″ adjustable
  • Drain Input Fittings: 1
  • Filter Socks: 1

EMERALD Water Flow

Trigger Emerald 34 Sump

 

Water enters the Emerald sumps into a dedicated section where the water will then flow over into Section 1. Section 1 where the interchangeable plate is located allowing for either filter sock or foam block mechanical filtration.  This area is covered with a lid to prevent water splashing. Water then flows out the bottom of Section 1 into section 2.

Section 2 is typically where the protein skimmer is located. Water then flows throught the "Trigger Symbol" cutout into Section 3.  Section 3 is the refugium section. the water then flows over teh second baffle through 2 perforated platforms and under the third baffle into Section 3. The top perforated platform comes with a foam block filter and the bottom one is open to use for several different filtration methods (bags of carbon, bio balls, rubble rock, etc.).

Section 4 is the return water section back into the tank.  This is where the return pump will sit.

Interchangeable Plates (Patent Pending)

Each Emerald sump comes with two plates that can be placed into Section 1:

  • Filter Sock Plate with 100 micron filter socks
  • Foam Block Distribution Plate with foam block

The Filter Sock Plate can be installed with filter socks.

Trigger Emerald 34 Sump

The Foam Block Distribution Plate is perforated with holes and can be used when filter socks are not desired or in the case when the filter socks need to be changed or cleaned but replacement socks are not readily available and you want to maintain some level of mechanical filtration. In this case, simply remove the Filter Sock Plate and install the Foam Block Distribution Plate with the foam block on top as shown in the lower picture to the right.

The Foam Block Distribution Plate may also be used on top of the Filter Sock Plate with filter socks installed. This will help to distribution the water more evenly across all socks so that the filter socks will last longer before clogging. This also helps to silence the water noise by slowing down and spreading the water more evenly across the surface area of all of the socks. The foam block filter can be placed on top of the Foam Block Distribution Plate as shown below to enhance even further the silencing and distribution of water and also allow even longer times before the socks become clogged by providing a pre-filter before the socks.

 Adjustable Water Level

Water level in the sump is adjustable from 7" to 9.5" to accommodate for the water height requirements for different protein skimmers.

Emerald 34 Sump

Emerald 34 Sump

Self Adjusting Foam Block (Patent Pending)

As the water level is adjusted by sliding the wall up and down, the foam block sponge filter and the perforated plate that it sits on will also move up and down automatically. This is important to maintain the correct location of the foam block sponge filter with respect to the sump water height. Not available on the EMERALD20C.

Emerald 34 Sump

Emerald 34 Sump

Probe Holder

All Emerald sumps come with a probe holder that can hold up to three probes. The two outside holes are 0.63” in diameter and the center hole is 0.8” in diameter to fit different sized probes.

Emerald 34 Probe Holder

Hose Holder

All Emerald sumps also come with 4 holes in the top support brace for holding in place 1/4” OD tubing from reactors, dosing pumps, ATO, etc.Emerald dosing tube holder

Laser Water Level

  

Subtle water level markings are laser engraved on the inside wall to help when setting the adjustable wall to the desired water level.

 

Additional Information

Additional Information

Manual No
Product Specs

Manufacturer

Manufacturer Trigger Systems

Reviews

Rizzo

Nice sump. Built pretty well. Wanted a refugium and that's why I went for this one.

Reefkpr

Purchased this Trigger systems sump to replace my glass sump with no baffles. The quality and craftsmanship of this sump far exceeded my expectations. Very nice layout and with the adjustable water height, my skimmer is performing better than ever. The baffles have also eliminated all microbubbles from entering the main display. Highly recommend this sump.

How do you rate this product? *

 
1 1 star
2 2 star
3 3 star
4 4 star
5 5 star
Quality
Price
Value